The Jockey Journal Board - Search Results

Go Back   The Jockey Journal Board > Search Forums

Showing results 1 to 25 of 359
Search took 0.02 seconds.
Search: Posts Made By: HRC
Forum: The Board 10-29-2017, 07:37 AM
Replies: 684
Views: 250,614
Posted By HRC
Forum: The Board 10-29-2017, 07:35 AM
Replies: 684
Views: 250,614
Posted By HRC
Re: The designated springer ID thread

Weird, wont let me post multiple pics...
Forum: The Board 10-29-2017, 07:34 AM
Replies: 684
Views: 250,614
Posted By HRC
Re: The designated springer ID thread

Anybody have an idea of manufacture on this one? Looks to be good quality or was at least.
Forum: The Board 10-26-2017, 04:42 PM
Replies: 9
Views: 2,013
Posted By HRC
Re: Denvers Swing Tail frames

Man, not much love for the Swing Tail, haha...I can definitely see the limitations of the design, and can see how you would get axle twist. That was why i was thinking to carry the small arms forward...
Forum: The Board 10-26-2017, 04:12 AM
Replies: 9
Views: 2,013
Posted By HRC
Re: Denvers Swing Tail frames

Yes, they basically had two small swingarms and a spring in top. Im missing the parts, so actually thought to make a loop like a reversed conventional SA to help rigidize and keep the two sides in...
Forum: The Board 10-25-2017, 04:25 PM
Replies: 9
Views: 2,013
Posted By HRC
Denvers Swing Tail frames

Good day! You don't see these too often. Does anybody have any knowledge of these? Where they used much for custom bikes? Did Denvers ever build bikes with these or just sell the frames? And...
Forum: The Board 02-12-2016, 02:38 AM
Replies: 684
Views: 250,614
Posted By HRC
Re: The designated springer ID thread

Gents,
DIdn't see this one anywhere in the thread, but many are missing pics these days. its about 4" in between the legs and 33" axle to bottom clamp. I'll fab a new bottom tree/stem and side arms...
Forum: Wanted 07-21-2015, 07:17 PM
Replies: 0
Views: 349
Posted By HRC
VL frame wanted

VL frame for a chop. Mainly the front half or neck needed, but if you got a complete, let me know whatcha got.
[email protected]
Forum: The Board 01-12-2015, 10:47 AM
Replies: 15
Views: 1,938
Posted By HRC
Re: Piston help needed!

be carefull cutting the domes, most are not solid in the last 30-40 years. I have some Panhead 9:1 Wisecos on the bench right now with a pretty decent dome and they are no thicker than a flat top,...
Forum: Wanted 01-12-2015, 07:23 AM
Replies: 0
Views: 503
Posted By HRC
rear Panhead heads

HI, looking for a pair of rear heads, '56 up style so I can run outside lines. For a dual rear headed project. bare is fine, needing repair is fine as they will be highly modified. Dont really want...
Forum: The Board 11-10-2014, 06:47 PM
Replies: 3,376
Views: 1,290,907
Posted By HRC
Re: Panheads Forever - Hottest pans ever! PICS

Not sure if I've put up my Pan. Not the hottest but did a 3000 mile trip this summer in a week from Tx to CO,NM and back. Was headed to Bonneville before it got rained out.
..Hans
Forum: Wanted 07-19-2014, 08:51 PM
Replies: 0
Views: 512
Posted By HRC
saddlebags to fit Pan rigid

need a set of usable bags for an upcoming trip. leather or hard. send me whatcha got.
thanks, Hans
Forum: The Board 07-09-2014, 04:22 PM
Replies: 32
Views: 3,174
Posted By HRC
Forum: The Board 07-09-2014, 04:14 PM
Replies: 3,376
Views: 1,290,907
Posted By HRC
Re: Panheads Forever - Hottest pans ever! PICS

4.00-18 front tire on this one?
Forum: The Board 04-30-2014, 08:57 AM
Replies: 247
Views: 120,857
Posted By HRC
Re: SISSY BAR thread

a recent sissy bar for a buddy...simple, strong and usefull.
Forum: The Board 01-10-2014, 05:28 AM
Replies: 247
Views: 120,857
Posted By HRC
Re: SISSY BAR thread

cool thread...bad from the dead...
Forum: Wanted 12-13-2013, 04:13 AM
Replies: 0
Views: 471
Posted By HRC
panhead rigid frame...

original as possible, in good shape. whatcha got?

thanks, hans
Forum: Wanted 12-13-2013, 04:10 AM
Replies: 1
Views: 676
Posted By HRC
T140 parts . crank, head and rocker covers

-crankshaft preferably ready to run
-head just needs to have no broken fins, can be complete or with valvetrain

thanks, Hans
Forum: The Board 09-04-2013, 06:01 PM
Replies: 6
Views: 1,343
Posted By HRC
Re: What does GME stand for?

General Motorcycle Engineering. Hollywood Ca
Forum: The Board 09-04-2013, 11:39 AM
Replies: 6
Views: 1,343
Posted By HRC
Re: What does GME stand for?

Yeah, I know, I was wondering what the letters stood for , like Goons & Monkeys Engineering
Forum: The Board 09-04-2013, 11:30 AM
Replies: 6
Views: 1,343
Posted By HRC
What does GME stand for?

As In The gas tank manf?
Forum: The Board 09-04-2013, 04:38 AM
Replies: 4,784
Views: 3,237,528
Posted By HRC
Forum: The Board 07-19-2013, 06:33 PM
Replies: 14
Views: 2,713
Posted By HRC
Re: Shovelhead grooved pistons!

And have your ring pack in hand so he can hone to suite and gap the rings if necesarry.
Forum: The Board 07-19-2013, 06:30 PM
Replies: 14
Views: 2,713
Posted By HRC
Re: Shovelhead grooved pistons!

I remember using NOS MC pistons in my BSA A65 back in the mid 90s and called for .0045-.005 for street use and .006-.007 for hipo/race. Being 21 yrs old i put them in a hair loose due to the fact...
Forum: The Board 07-19-2013, 09:41 AM
Replies: 14
Views: 2,713
Posted By HRC
Re: Shovelhead grooved pistons!

Those are old MC brand pistons. High quality forged back in the day, but low silicon so they expanded alot, requiring more clearance than usual cast. Personally, id NOT get KB....
Hans
Showing results 1 to 25 of 359

 
Forum Jump

All times are GMT -5. The time now is 03:17 PM.