The Jockey Journal Board - Search Results

Go Back   The Jockey Journal Board > Search Forums

Showing results 1 to 25 of 373
Search took 0.02 seconds.
Search: Posts Made By: dan r
Forum: The Board Today, 08:52 AM
Replies: 3
Views: 92
Posted By dan r
Re: Plating in a neck correctly

If your plates let water in and trap it there, yes there will be a rust problem.
If your plates are fully welded and are sealed, no need to worry about sealers or rust prevention.

Oxygen is the...
Forum: The Board Today, 08:46 AM
Replies: 6
Views: 164
Posted By dan r
Re: 1965 motor and tranny in a 58-64 frame

Yes, a complete engine, trans and primary from an e start will bolt into a kick only frame.
Trans and engine mounting is all the same.
The rear chain run is in the same location off set from...
Forum: The Board 06-01-2020, 11:29 AM
Replies: 6
Views: 164
Posted By dan r
Re: 1965 motor and tranny in a 58-64 frame

Think about what major changes and why to produce the first e start big twins.
Frame tubes were raised to clear a different oil tank and battery.
The oil tank was changed to gain room for the...
Forum: The Board 05-14-2020, 03:55 PM
Replies: 23
Views: 570
Posted By dan r
Re: Case stud question

Use a shop vac to suck any debris that will fall out of the bottom of the stud holes before, during and after. Yes there will be all sorts of bad things fall onto the flywheels when doing this. Be...
Forum: The Board 03-24-2020, 10:40 AM
Replies: 2
Views: 614
Posted By dan r
Re: Kn 93/ kn 74 s&s

Bore and stroke will be different.
Crankcases for the 93 are bored larger for the 3 5/8" bore cylinders, past that, they are the same.
Flywheels are different stroke but they both share the same...
Forum: The Board 03-24-2020, 07:59 AM
Replies: 16
Views: 1,166
Posted By dan r
Re: let's talk seats for bit

That bike was the inspiration I had to build mine. I didn't want a copy but my version of a like style. I wanted something of a super glide style before there were super glides.
Forum: The Board 03-24-2020, 07:30 AM
Replies: 16
Views: 1,166
Posted By dan r
Re: let's talk seats for bit

Very nice, thanks for showing that.
Forum: The Board 03-23-2020, 11:08 AM
Replies: 16
Views: 1,166
Posted By dan r
Re: let's talk seats for bit

Thanks guys.
Was looking at my fxr that has a hinge on one side and a latch on the other. Always liked that but it wouldn't adapt to well.

After looking here and then at the links 750Devo put...
Forum: The Board 03-22-2020, 12:07 PM
Replies: 16
Views: 1,166
Posted By dan r
let's talk seats for bit

I am no seat maker, wish I was.

I have a big twin 4 speed swing arm bike. The frame is a 64 that some may call a step down or drop seat frame. It's a frame that's more or less used 58-64 until...
Forum: The Board 03-19-2020, 11:24 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

The cam in this pic is the mildest S&S generator engine case type cam they make. It's roughly about the same as an Andrews A2 cam far as lift and duration goes. This one was also made to use their...
Forum: The Board 03-19-2020, 10:24 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

pretty much true about finding good and or bad mods. quite often good and bad can be found with older engines of all ages. I tend to think it started way before the 60's though. these last few years...
Forum: The Board 03-19-2020, 01:31 PM
Replies: 26
Views: 1,075
Posted By dan r
Re: shovelhead clutch

here's a few random thoughts...
oem stock friction plates must be free of any type of oil. if your running the red alto brand fiber friction plates or any Kevlar type, they do need to be first...
Forum: The Board 03-19-2020, 01:10 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

right, don't mix and match flywheel sets, use a complete flywheel set from the same donor engine. The tapers changed roughly early or mid 81 so a 80 or older shaft won't work in a later wheel. If you...
Forum: The Board 03-19-2020, 12:57 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

Oil flow in a converted crankcase will now work like in these pix. First pic shows what gets full pump pressure. Oil under regulated pressure will enter the crankcase half from the pump. It will...
Forum: The Board 03-19-2020, 11:59 AM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

Another thing you will need to do to convert a generator engine to pinion end oiling is use a later design split system pump. A pump that is made for end oiling is different. A 73 and later pump has...
Forum: The Board 03-19-2020, 10:31 AM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

ok, I take it you have a complete 84 shovel engine.
You are wanting a generator right case added to it but don't have one yet.

an 84 crankshaft is a good start. It will have evo type rods and...
Forum: Tech Archives 03-17-2020, 11:28 PM
Replies: 20
Views: 971
Posted By dan r
Re: Alt left case Gen R case motor?

hold on a bit... if all would like, I found some pix of most of the case and cam cover mods I do to convert to end oiling plus a few other related pix such as cam lobe to timer gear interference...
Forum: The Board 03-17-2020, 11:28 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

hold on a bit... if all would like, I found some pix of most of the case and cam cover mods I do to convert to end oiling plus a few other related pix such as cam lobe to timer gear interference...
Forum: Tech Archives 03-17-2020, 02:19 PM
Replies: 20
Views: 971
Posted By dan r
Re: Alt left case Gen R case motor?

oops, I screwed up...

oil pumps... for side oiling, use a 72 or older oem or an s&s replacement for 69 and older.

for end oiling, use an s&s 69 and older replacement. then make all...
Forum: The Board 03-17-2020, 02:19 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

oops, I screwed up...

oil pumps... for side oiling, use a 72 or older oem or an s&s replacement for 69 and older.

for end oiling, use an s&s 69 and older replacement. then make all...
Forum: Tech Archives 03-17-2020, 01:43 PM
Replies: 20
Views: 971
Posted By dan r
Re: Alt left case Gen R case motor?

to get things back on track with will this work or what works and more importantly what won't work...

a 70 to 84 shovel case half will be needed to start with.
yes, a 58-69 right case half will...
Forum: The Board 03-17-2020, 01:43 PM
Replies: 47
Views: 2,697
Posted By dan r
Re: Alt left case Gen R case motor?

to get things back on track with will this work or what works and more importantly what won't work...

a 70 to 84 shovel case half will be needed to start with.
yes, a 58-69 right case half will...
Forum: The Board 03-11-2020, 05:17 PM
Replies: 18
Views: 940
Posted By dan r
Re: Right Case bearing race 64 panhead

another vote for line lap then start the measurement/evaluation process.

To me it looks as that race has had a once over lightly with some sort of sand paper or emery cloth... I see fresh...
Forum: The Board 04-17-2019, 06:19 AM
Replies: 8
Views: 459
Posted By dan r
Re: 37 uh

Whole lot of bits and pieces of un related 80 inch shovel parts...

https://www.youtube.com/watch?v=zwO_Pvc7OYw


and a 80 inch snow shovel...

https://www.youtube.com/watch?v=cTyETFeqax0
...
Forum: The Board 04-17-2019, 06:11 AM
Replies: 8
Views: 459
Posted By dan r
Re: 37 uh

ok, here's a 16 J model. It has JD flywheels so it's stroked from 61 inch to 71. something inch.

https://www.youtube.com/watch?v=nqfNayPGQJc


Here's a stock 1953 61 inch EL pan......
Showing results 1 to 25 of 373

 
Forum Jump

All times are GMT -5. The time now is 11:21 AM.