Forum: The Board
10-21-2018, 05:37 PM
|
|
Replies: 1
Views: 572
|
|
Forum: The Board
10-21-2018, 05:35 PM
|
|
Replies: 1
Views: 572
Sprocket alignment
I'm having a hard time figuring out my engine sprocket and clutch alignment problem on my 57 triumph trw. I assembled my clutch (new basket, cush rubbers, fibers, and springs) and pressed my engine...
|
|
Forum: The Board
07-25-2018, 10:47 PM
|
|
Replies: 3
Views: 655
|
|
Forum: The Board
07-25-2018, 09:32 PM
|
|
Replies: 3
Views: 655
More triumph wiring questions
I have a 1957 triumph trw that is on the last bit of restoration. I got a NOS wiring harness for it (It matches up with the diagram in the picture). I got an adapter ring to run the newer...
|
|
Forum: The Board
09-21-2017, 12:24 AM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
I swear I will post more pics once I start making real progress. I want to put the rear wheel on this weekend but need some knowledge first. I didn't want to start a new thread so hopefully I can get...
|
|
Forum: The Board
08-21-2017, 10:13 PM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
Well poo big after thought isn't what I was going for haha. doggydaddy is right about the bolt clearance being too tight but so was the comment about running the flanges 90 degrees from each other. I...
|
|
Forum: The Board
08-21-2017, 01:18 AM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
I got the 45 degree fitting this weekend that was perfectly recommended to me. I had to trim it down a bit and then I started making a flange from mild steel that I will eventually tig weld the...
|
|
Forum: The Board
08-19-2017, 02:17 AM
|
|
Replies: 48
Views: 4,191
|
|
Forum: The Board
08-14-2017, 11:08 PM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
thanks for the compliments guys! I got my elbow coming but the big news is I finally got that flange off the carb. If anyone is on the fence about ordering the jrc carbs from lowbrow because they are...
|
|
Forum: The Board
08-14-2017, 09:16 AM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
That is perfect I didn't even think of that. Thanks I will be ordering that tonight. I can polish it instead of painting too!
|
|
Forum: The Board
08-13-2017, 10:55 PM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
If its not a flathead why is it so slow haha. I didn't get much of anything done I spent all day looking at wedding venues. That alone almost killed me! Since I didn't deliver on progress I will give...
|
|
Forum: The Board
08-10-2017, 11:58 PM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
This is the bike its going on. I spent a lot of time milling an aluminum spacer to push the carb back enough to clear the distributor but that puts the carb to close to the seat post. The original...
|
|
Forum: The Board
08-10-2017, 12:12 AM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
well it looks like I will be making a manifold this weekend. Thanks for the input. One more question gang. I'm gonna make the manifold of steel and connect to the carb with a rubber boot. will the...
|
|
Forum: The Board
08-07-2017, 11:55 PM
|
|
Replies: 35
Views: 2,369
Re: angle of the dangle
Ok good I just figured the angle might introduce more fuel to one cylinder then the other. Just put to much thought into it then.
|
|
Forum: The Board
08-07-2017, 11:08 PM
|
|
Replies: 35
Views: 2,369
angle of the dangle
Howdy all. I'm having clearance trouble with a carb and air cleaner I'm trying to use on my triumph trw. The carb is a jrc 26mm from lowbrow and the air cleaner is an emgo offset pancake filter. You...
|
|
Forum: The Board
02-20-2017, 09:46 PM
|
|
Replies: 1
Views: 807
cadmium plating question
I just got back a bucket of bolts, nuts, and random parts from being cad plated for my triumph restoration. I had my gearbox camplate, quadrant, and gearchange spindle plated. I figured I would...
|
|
Forum: The Board
10-06-2016, 12:57 PM
|
|
Replies: 5
Views: 818
|
|
Forum: The Board
10-04-2016, 03:11 PM
|
|
Replies: 5
Views: 818
|
|
Forum: The Board
10-03-2016, 11:26 PM
|
|
Replies: 5
Views: 818
learning about tappets
I have four tappets I am wanting to resurface myself for my first triumph engine rebuild (TRW). There is some wear to them. 3 of them have slight indentations in the center of the face. My goal was...
|
|
Forum: The Board
09-09-2016, 05:51 PM
|
|
Replies: 3
Views: 649
Scavenge pipe?
Hello guys I already did my intro. Again. I lost my account and wasn't able to recover it. I went by codyp. Anyways I have been building my first triumph engine (trw flathead 500) and I didn't check...
|
|
Forum: New? Introduce yourself here!
09-09-2016, 12:32 AM
|
|
Replies: 2
Views: 481
Here again
Hello all. My account was lost and could not be restored. I have been a member since the age of the Dragon. I joined when I was 14 I just recently turned 27. Yes I waisted that much of my life on a...
|
|
Forum: The Board
03-20-2016, 12:44 AM
|
|
Replies: 13
Views: 3,153
|
|
Forum: The Board
12-13-2015, 05:46 PM
|
|
Replies: 0
Views: 1,143
triumph and prs8 wiring help
I'm messing around with a nos wiring harness for my mk2b TRW triumph and I'm a little stuck. The harness I bought from burton bike bits is correct for my bike but doesn't match my wiring diagrams in...
|
|
Forum: Parts For Sale
11-19-2015, 11:05 PM
|
|
Replies: 8
Views: 1,653
|
|
Forum: Parts For Sale
11-15-2015, 08:28 PM
|
|
Replies: 8
Views: 1,653
|
