Forum: The Board
01-22-2019, 01:43 PM
|
|
Replies: 7
Views: 616
Thanks for the tips. I surfaced carb bowls,...
Thanks for the tips. I surfaced carb bowls, backed out slide stop screws 1 turn more after it moved slide and buttoned up vacuum line and it fired and idled.
Looks like it was warped surfaces,...
|
|
Forum: The Board
01-21-2019, 09:51 PM
|
|
Replies: 7
Views: 616
72 triumph bonneville very high idle..still
I have done countless hours of research to no avail. Keyway on shaft broke and took a couple years to fix. Rebuilding her now. Cleaned carbs and wet sanded slides and mating surfaces w 1500. Points...
|
|
Forum: The Board
11-01-2018, 05:28 PM
|
|
Replies: 8
Views: 822
|
|
Forum: The Board
11-01-2018, 05:26 PM
|
|
Replies: 7
Views: 1,132
|
|
Forum: The Board
11-01-2018, 04:43 PM
|
|
Replies: 14
Views: 3,703
Re: 4 Speed Triumph Tranny Indexing?
A couple updates.
Shifts through gears but has what feels like %30 power in first gear.
Basically feels like it is in second gear
Took everything apart and inspected each gear, shaft, groove,...
|
|
Forum: The Board
09-12-2018, 01:48 PM
|
|
Replies: 16
Views: 3,417
|
|
Forum: The Board
09-06-2018, 03:27 PM
|
|
Replies: 16
Views: 3,417
|
|
Forum: The Board
07-16-2015, 09:46 PM
|
|
Replies: 16
Views: 3,417
|
|
Forum: The Board
07-13-2015, 02:26 PM
|
|
Replies: 16
Views: 3,417
|
|
Forum: The Board
07-13-2015, 02:11 PM
|
|
Replies: 54
Views: 4,804
Re: Panhead headache need some advice
Been down this exact same road before.
For what it's worth... All wires and connections clean? New Properly gapped plugs, I welded a washer in the end of the drag pipes to create a bit of back...
|
|
Forum: The Board
12-05-2014, 01:49 PM
|
|
Replies: 21
Views: 3,632
Re: Dad's '39 Knuck
Great job looks like your off to a good start, I bought a knuck off my mom after we buried my old man.
It's a lot of fun and there is a ton of good info on here.
I would inspect tires, order a...
|
|
Forum: The Board
11-18-2014, 04:20 PM
|
|
Replies: 61
Views: 11,606
|
|
Forum: The Board
11-17-2014, 09:40 PM
|
|
Replies: 8
Views: 1,536
|
|
Forum: The Board
11-16-2014, 08:46 AM
|
|
Replies: 8
Views: 1,536
|
|
Forum: The Board
11-14-2014, 12:48 PM
|
|
Replies: 8
Views: 1,536
|
|
Forum: The Board
11-14-2014, 09:31 AM
|
|
Replies: 16
Views: 2,807
Re: thickness of leather for wrapping seat?
My 2 cents:
I like the thicker stuff 6-11oz+ cut and set on top of thin foam baseball stitched to the pan but it's expensive and allot of work to punch holes in the pan and the cowhide. More...
|
|
Forum: The Board
11-14-2014, 08:48 AM
|
|
Replies: 8
Views: 1,536
|
|
Forum: The Board
08-29-2014, 10:20 AM
|
|
Replies: 226
Views: 63,253
|
|
Forum: The Board
08-29-2014, 10:11 AM
|
|
Replies: 15
Views: 1,826
Re: Nitrous on a '46 Indian Chief
Maybe we should run a special thanks thread as I know I've gotten some difficult shit sorted out on here. I would love to see n20 on something pre circa 57 other than my soon to be Chevy.
|
|
Forum: The Board
08-16-2014, 11:35 PM
|
|
Replies: 6
Views: 1,303
Re: Triumph Gearbox Help '76 T140
May get lucky but worse case:
Doubt plates are stuck together but couldn't hurt to pull them out resurface a bit on smooth concrete , soak in oil and reassemble.
May want to pop kicker cover and...
|
|
Forum: The Board
08-11-2014, 09:05 PM
|
|
Replies: 23
Views: 3,115
Re: surging at part throttle
It could be the stuff that's so simple it gets overlooked like the little caps on top of spark plugs were a bit loose or gapped off, or a electrical connection at coil or points needed a cleaning,...
|
|
Forum: The Board
08-11-2014, 08:57 PM
|
|
Replies: 113
Views: 27,397
|
|
Forum: The Board
08-11-2014, 08:42 PM
|
|
Replies: 15
Views: 2,013
Re: Stripped case studs head bolts. 1947FL
Finally after a long and arduous process, 2 months +, 103 beers, a small pinch of profanity and a couple of tears in the corner of defeat we finally got some inserts to ducking take.
Coarse...
|
|
Forum: The Board
08-11-2014, 08:26 PM
|
|
Replies: 46
Views: 7,820
|
|
Forum: The Board
08-05-2014, 06:16 PM
|
|
Replies: 7
Views: 862
Re: Budget torch setup for fabricating?
+1 on everything mentioned above there's some
experts up there. I see small run and gun ac repairman style complete set ups at pawn shops for about $100. Most welding supply houses will give you a...
|
