The Jockey Journal Board - Search Results

Go Back   The Jockey Journal Board > Search Forums

Showing results 1 to 25 of 298
Search took 0.01 seconds.
Search: Posts Made By: kngkong
Forum: The Board 01-31-2019, 12:33 AM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Mule,

:D No worries. I appreciate being able to talk about all the options before deciding what I'm going to do. When I started out this thread I was hoping to find someone that could say "Yeah,...
Forum: The Board 01-30-2019, 10:59 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Rich bob,

I know this is just a bodge fix and I donít think Iíll need to resort to this but thought I would mention I might be hesitant to put anything into the crack under the washer which might...
Forum: The Board 01-30-2019, 08:30 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Mm, good point. I could go without the counterbore and always do it at a later date when the engine is apart.
Forum: The Board 01-30-2019, 07:33 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Farmall,

Driving the counterbore from the bottom might not be so easy. I thought it might be the case and just checked. The case boss where the breather stud goes through blocks a straight shot...
Forum: The Board 01-30-2019, 07:18 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Yup, I'll be checking the bottoms too. Thanks Mule!
Forum: The Board 01-30-2019, 05:29 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Farmall,

Thanks for your reply by the way. This all sounds like a good plan.

I was thinking the reverse counterbore might be the ticket.

Cheers
Forum: The Board 01-30-2019, 03:52 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

I loosened up all the bolts last night to double check the rest of mounts. Back right top could use a spot face touchup, nowwhere near as bad as the left. Still need to take a look at the front tabs.
Forum: The Board 01-30-2019, 03:45 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

I can do the machining. Just didn't know what you meant by mating surfaces. Confused as I thought you meant the case halfs.

Thanks!
Forum: The Board 01-30-2019, 02:34 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Mule,

Are you expecting that there would be so much warpage from the weld repair that the mating surfaces on the case half's will need truing?

Is that what you mean?
Forum: The Board 01-29-2019, 04:45 PM
Replies: 50
Views: 3,564
Posted By kngkong
Forum: The Board 01-29-2019, 04:44 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Mule,

It's not Winter here in New Zealand! It's the middle of awesome summer riding weather. Plus the fact that I just got everything back together after fixing a bunch of stuff. Everything was...
Forum: The Board 01-29-2019, 04:17 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Mm, you mean to get the washer surface flat? Thanks. Yeah, I'll consider that as a last resort. I'm hoping I can figure something out.
Forum: The Board 01-29-2019, 04:05 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Jaws,

Are you asking me?
Forum: The Board 01-28-2019, 08:49 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

And disassemble the cases?
Forum: The Board 01-28-2019, 07:36 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

Thanks for the advice!

Relieved that no one is saying tear this down immediately and tig this up. Like I said it seems like this was due to the surface under the washer being dished and when I...
Forum: The Board 01-23-2019, 02:02 PM
Replies: 50
Views: 3,564
Posted By kngkong
Thanks! I know about the green loctite. But...

Thanks! I know about the green loctite. But you’re suggesting I try using it in the crack to give it some extra strength?
Forum: The Board 01-22-2019, 11:51 PM
Replies: 50
Views: 3,564
Posted By kngkong
I’m a little relieved that you’re saying to let...

I’m a little relieved that you’re saying to let it be for a while. Since this motor probably has about 100 miles on it might be a while until the next time I pull it apart though.
Forum: The Board 01-22-2019, 11:26 PM
Replies: 50
Views: 3,564
Posted By kngkong
John, Are you saying to put the green...

John,

Are you saying to put the green loctite in the crack?

Yeah, the area under the washer was dished out and when tightened the washer distorted created a wedge.
Forum: The Board 01-22-2019, 11:23 PM
Replies: 50
Views: 3,564
Posted By kngkong
Joe, Fortunately my timing hole is in good...

Joe,

Fortunately my timing hole is in good shape and not a tapered thread. I try to take care of that.
Forum: The Board 01-22-2019, 03:28 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

This is on a 1937 Knucklehead.
Forum: The Board 01-22-2019, 03:10 PM
Replies: 50
Views: 3,564
Posted By kngkong
Re: Cracked rear left motor mount hole

I took the bolt out the other night. The area under the washer was not faced properly and was dished.

If it is possible to TIG this without disassembling the engine does anyone have any ideas on...
Forum: The Board 01-22-2019, 03:09 PM
Replies: 50
Views: 3,564
Posted By kngkong
Cracked rear left motor mount hole

Discovered this a couple of nights ago. Would anyone in their right mind ever consider repairing this without completely dismantling the cases? Looks the washer is distorted and creating outward...
Forum: The Board 03-21-2016, 12:12 AM
Replies: 13
Views: 3,391
Posted By kngkong
Re: PreUnit rear wheel bearings: Swap tapered Timken for sealed?

Ha. I'm not blaming this one of the metric/imperial system. Purely lack of sleep. Though I don't know what's the better excuse.
Forum: The Board 03-20-2016, 08:52 PM
Replies: 13
Views: 3,391
Posted By kngkong
Re: PreUnit rear wheel bearings: Swap tapered Timken for sealed?

I'm American and think in inches but go back and forth since I've moved. Yeah, you're right 9/16" my mistake. I was in fact converting those metric to imperial right after I took them.
Forum: The Board 03-20-2016, 05:55 PM
Replies: 13
Views: 3,391
Posted By kngkong
Re: PreUnit rear wheel bearings: Swap tapered Timken for sealed?

And they do have one with a 1/2" inner bore #2782T71 but not sure if that will end up being too tight. Will remeasure my axle.
Showing results 1 to 25 of 298

 
Forum Jump

All times are GMT -5. The time now is 09:48 PM.