Forum: The Board
11-27-2020, 09:21 PM
|
|
Replies: 6
Views: 527
|
|
Forum: The Board
11-07-2020, 09:18 PM
|
|
Replies: 10
Views: 604
I'm my experience every v twin I've owned runs...
I'm my experience every v twin I've owned runs richer in the rear cylinder. Not a lot richer but noticable when comparing the front and rear plugs. I would recommend pressurizing your manifold and...
|
|
Forum: The Board
06-11-2020, 05:08 PM
|
|
Replies: 5
Views: 550
Rhys, are you missing the simplicity of the...
Rhys, are you missing the simplicity of the flathead yet? Just giving ya S$%T. Like my uncle who worked at the Juneau ave plant used to say "buy a harley, buy the best! Ride a mile, walk the rest"
|
|
Forum: The Board
06-05-2019, 02:45 PM
|
|
Replies: 103
Views: 22,842
|
|
Forum: The Board
06-01-2019, 02:20 AM
|
|
Replies: 5
Views: 761
|
|
Forum: The Board
05-31-2019, 06:00 PM
|
|
Replies: 5
Views: 761
Timing a U model with T&O wheels
I was just rechecking my timing on my 37U and noticed the timing mark is way towards the front of the inspection hole as the points just start to open. I've had other flatheads and it was always just...
|
|
Forum: The Board
05-24-2019, 12:37 PM
|
|
Replies: 20
Views: 1,655
Re: CV carb tuning issues
The DJ emulsion tube has a smaller threaded opening for the main jet to screw into than the OEM one. The pilot jets from DJ are the same as OEM ones, at least as far as I can tell. Based on the main...
|
|
Forum: The Board
05-24-2019, 10:32 AM
|
|
Replies: 20
Views: 1,655
|
|
Forum: The Board
05-23-2019, 11:53 PM
|
|
Replies: 20
Views: 1,655
|
|
Forum: The Board
05-22-2019, 09:13 PM
|
|
Replies: 20
Views: 1,655
Update! I've added a cv performance needle and...
Update! I've added a cv performance needle and cant say enough good about it. The bike runs like a different machine. Throttle is snappy and way more responsive than it was with the dynojet needle....
|
|
Forum: Jock Shops
05-17-2019, 11:16 PM
|
|
Replies: 345
Views: 107,026
|
|
Forum: New? Introduce yourself here!
05-13-2019, 11:42 PM
|
|
Replies: 1
Views: 592
|
|
Forum: The Board
05-13-2019, 10:45 PM
|
|
Replies: 3
Views: 799
Flathead Oil Upgrade
Here is a couple of photos of the oil upgrade for flatheads. I had this done with the 4 vane pump on my own bike. I've had other flatheads and I swear it feels like a cooler running engine. My last...
|
|
Forum: The Board
05-11-2019, 10:37 PM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-06-2019, 08:14 PM
|
|
Replies: 13
Views: 1,567
|
|
Forum: The Board
05-05-2019, 08:12 PM
|
|
Replies: 31
Views: 1,360
Judging by the way it ran and the color of the...
Judging by the way it ran and the color of the plugs I dont think the leak matters. When I pumped up the manifold with a hand pump to 5 psi it held fine. I was using too.much pressure.
I've got a...
|
|
Forum: The Board
05-04-2019, 07:44 PM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-04-2019, 11:53 AM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-03-2019, 09:01 PM
|
|
Replies: 31
Views: 1,360
Yes, I've got a plate on the manifold and am...
Yes, I've got a plate on the manifold and am using air with soapy water to make sure it's all sealed up. (I will use less psi going forward) Air is escaping out the rear intake valve cover and making...
|
|
Forum: The Board
05-03-2019, 07:01 PM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-03-2019, 07:01 PM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-03-2019, 06:51 PM
|
|
Replies: 31
Views: 1,360
|
|
Forum: The Board
05-03-2019, 05:27 PM
|
|
Replies: 31
Views: 1,360
Valve cover air leak
Well I decided to do a bubble check on my intake after heat cycling my new top end (37u motor) I apply 10-12 psi and air escapes through my rear cylinder valve cover. I closed it and sprayed it and...
|
|
Forum: The Board
03-12-2019, 03:50 PM
|
|
Replies: 40
Views: 2,331
Re: Noise from clutch basket under load
I had a very similar noise with mine when I first installed a tamer. I eventually pulled it back apart and rechecked the gap. Do you have one? If I remember right it was not shimmed properly. I reset...
|
|
Forum: The Board
02-22-2019, 11:21 AM
|
|
Replies: 4
Views: 4,839
|
