Forum: The Board
09-29-2014, 03:02 PM
|
|
Replies: 6
Views: 2,028
Re: harbor freight mini hvlp gun questions
Don't forget to rinse the gun, including the air side before putting any paint through it. The oil/ grease they ship in the air side of the gun will ruin your paint job real quick.
I shot this a...
|
|
Forum: The Board
04-29-2013, 02:09 PM
|
|
Replies: 46
Views: 8,968
Re: Remote Filter Option/Pics
My filter used to mount to the front engine mount.
After the bracket tabs broke I cut the remainder of the tabs off and drilled 2 holes to mount it to the front of the trans bearing support....
|
|
Forum: The Board
12-18-2012, 02:51 PM
|
|
Replies: 42
Views: 6,178
Re: super nut?
Revtech makes a final drive gear for the earlier 4spds with the O-ring groove.
|
|
Forum: The Board
12-18-2012, 12:36 PM
|
|
Replies: 42
Views: 6,178
Re: super nut?
My main drive gear was trashed from someone cranking the sprocket nut with an impact, or hamfisting the seal in it. I replaced the gear with an Andrews main drive gear that had the groove for an...
|
|
Forum: The Board
12-22-2011, 08:49 PM
|
|
Replies: 3,376
Views: 1,318,652
|
|
Forum: The Board
12-20-2011, 05:57 PM
|
|
Replies: 37
Views: 17,307
Re: Single down tube shovelhead?
The first one is beautiful, but might look better with mid controls. The second one well.....I think I'll steer clear of the styling or commentary on that winged wonder.
|
|
Forum: The Board
12-19-2011, 12:21 PM
|
|
Replies: 37
Views: 17,307
Re: Single down tube shovelhead?
I plan on running two lower rails and a single down tube. I thought about the single loop style frame, but I will continue to run forward controls. I think the single loop style frame looks cleaner...
|
|
Forum: The Board
12-16-2011, 10:28 AM
|
|
Replies: 37
Views: 17,307
Single down tube shovelhead?
I have seen a number of big twins in single down tube rigid frames, mostly show bikes, but never had the chance to ride one.
I'm pondering a different frame for my shovel and thinking about a...
|
|
Forum: The Board
01-18-2010, 04:51 PM
|
|
Replies: 8
Views: 775
|
|
Forum: The Board
01-18-2010, 04:41 PM
|
|
Replies: 8
Views: 775
|
|
Forum: The Board
01-18-2010, 03:21 PM
|
|
Replies: 48
Views: 21,858
Re: Simplex ?
If this works here are a couple of clips, not mine. The first one looks like he's moving towards the end.
http://www.youtube.com/watch?v=Z4d308R0xlg
http://www.youtube.com/watch?v=KLWe8pfCSnc
|
|
Forum: The Board
01-30-2006, 10:20 AM
|
|
Replies: 48
Views: 21,858
Re: slightly off topic simplex service cycle
A pristine Servi-Cycle can pull about $4k-$5k tops.
They are not too common, and finding an engine for one can be difficult. The original engines didn't hold up well and its not uncommon to find the...
|
|
Forum: The Board
10-18-2005, 02:23 PM
|
|
Replies: 22
Views: 2,384
Re: 76 Ironhead starter set up?
You can put a starter on it if you have clearance, if your clutch basket has a ring gear, if your cam cover has the notch out for the starter, if your trans sprocket cover has the starter notch. Its...
|
|
Forum: The Board
06-01-2005, 07:04 PM
|
|
Replies: 1,362
Views: 624,964
Re: Show your bike pics
Huh!!!
Closest translation I could find was something like:
"Attention! End left is forbidden"
|
|
Forum: The Board
06-01-2005, 06:56 PM
|
|
Replies: 1,362
Views: 624,964
Re: Show your bike pics
Mike I'm about 30 min. northeast of you. Just west of Flint off of I-69.
I will probably be selling off some misc. XS stuff after I get farther along on the projects (read started). See Ya at BP05...
|
