The Jockey Journal Board

The Jockey Journal Board (https://www.jockeyjournal.com/forum/index.php)
-   The Board (https://www.jockeyjournal.com/forum/forumdisplay.php?f=2)
-   -   trio of trumps (https://www.jockeyjournal.com/forum/showthread.php?t=55195)

image1 06-05-2009 12:46 PM

trio of trumps
 

fucker's seem to be multiply-ing in my shop. Waiting on my crank(S) to get back from the machine shop, and another box of parts, but this is what i have ahead of me....
looks fun huh?

http://i214.photobucket.com/albums/c...t/100_0914.jpg
http://i214.photobucket.com/albums/c...t/100_0916.jpg
http://i214.photobucket.com/albums/c...t/100_0919.jpg

not45blesk 06-05-2009 12:51 PM

Re: trio of trumps
 

Goody Good ... !!!

All seem nine stud though.

Talk about an artistic display...

Probably it should show on friday art too.

keep it up

caveman 06-05-2009 01:04 PM

Re: trio of trumps
 

looks to me that you had driven the middle one with to high rpm,s ( broken rod) :D

image1 06-05-2009 01:09 PM

Re: trio of trumps
 

Quote:

( broken rod)
actually, all of these are broken rod motors...
1. open primary clutch bearing went
2. po reversed oil lines and spun rod
3. sludge trap, spun rod
4. not sure, but crank was WASTED, several thousandths below min spec for a -.020

image1 06-08-2009 08:47 AM

Re: trio of trumps
 

After watching TroyFab's build, and his 'shark fin' removal i decided i REALLY liked that look, and so i did it on my engine as well, but i also went a little further and cut off the top section of the cover AND the outer transmission housing. I rounded it all out and blended the housing to where it looks factory. I'm stoked about how it all came out, looks kinda like pre-unit in a way.

Stock Example:
http://i214.photobucket.com/albums/c...ge1art/044.jpg
http://i214.photobucket.com/albums/c...ge1art/045.jpg


After Modifications:
http://i214.photobucket.com/albums/c...ge1art/040.jpg
http://i214.photobucket.com/albums/c...ge1art/042.jpg
http://i214.photobucket.com/albums/c...ge1art/041.jpg

lowlife_slim 06-08-2009 04:48 PM

Re: trio of trumps
 

i aint clicking that shit... :)

looks like you have a lot of man-hours ahead of you. good luck.

Bozi 06-08-2009 08:21 PM

Re: trio of trumps
 

Got an extra head? :-)

Post up some pics as you go with one of them.\

You got bikes, or are you in starting stages of a build or 2 or 3?

76flh 06-08-2009 11:27 PM

Re: trio of trumps
 

Man! that looks cool with all those trump parts laying on the floor like that.

good luck,
76flh

Drakkule 06-08-2009 11:50 PM

Re: trio of trumps
 

I'm willing to adopt one of them, i promise to give it a good home.

image1 06-09-2009 08:51 AM

Re: trio of trumps
 

Quote:

Got an extra head? :-)
no, i'm lookin for a single carb head too...

Quote:

You got bikes,
This is one (its under going some changes)
http://i214.photobucket.com/albums/c...t/IMG_0129.jpg

This is the other

http://i214.photobucket.com/albums/c...t/SANY0805.jpg

image1 06-09-2009 08:53 AM

Re: trio of trumps
 

got some more work done last night on the 'hot rod' motor. Finally tracked down a lay shaft 3rd gear (hard to find 5 spd parts) and got the transmission all put back together, new bearings throughout. Also did some more fat trimming. I am retro-fitting (this is a 71 tr6) earlier style cam wheels to some Megacycle cams to go in this engine, and decided that they needed to lose some weight.

Stock timing gear set, thick and bulky

http://i214.photobucket.com/albums/c...608092256a.jpg
http://i214.photobucket.com/albums/c...608092256b.jpg


Earlier (68) timing gears, on a diet.

http://i214.photobucket.com/albums/c...608092257a.jpg
http://i214.photobucket.com/albums/c...608092257b.jpg
http://i214.photobucket.com/albums/c...608092054a.jpg

image1 06-17-2009 10:27 AM

Re: trio of trumps
 

tag/tail light mount done, coil mount done, battery box done. Pics.

*fender fits nicely, but wheel has no bearings and is not sitting straight at all.

http://farm4.static.flickr.com/3411/...2761fd9e_o.jpg
http://farm3.static.flickr.com/2447/...383faefd_o.jpg
http://farm4.static.flickr.com/3352/...ec845208_o.jpg
http://farm4.static.flickr.com/3367/...bea59b24_o.jpg

6T Sinner 06-17-2009 11:26 AM

Re: trio of trumps
 

Those timing gears look nice! How'd you do it?

image1 06-17-2009 12:05 PM

Re: trio of trumps
 

thanks. layed out a pattern, made a jig to hold them true in the drill press, and then just rotated the gear in the fixture to keep spacing the same.

image1 07-07-2009 09:55 AM

Re: trio of trumps
 

some gooder pics from last night. Its bare bones, no frills for sure. Dude is bout outta money so its not getting any fancy stuff. Engine for this one is getting close to being done.

http://i214.photobucket.com/albums/c...1art/012-1.jpg
http://i214.photobucket.com/albums/c...1art/014-1.jpg
http://i214.photobucket.com/albums/c...ge1art/019.jpg
http://i214.photobucket.com/albums/c...ge1art/018.jpg
http://i214.photobucket.com/albums/c...1art/015-1.jpg

Ken Cormier 07-07-2009 12:34 PM

Re: trio of trumps
 

Man I like that style

VOH 07-07-2009 12:40 PM

Re: trio of trumps
 

Quote:

Originally Posted by image1 (Post 496327)
no, i'm lookin for a single carb head too...



This is one (its under going some changes)
http://i214.photobucket.com/albums/c...t/IMG_0129.jpg

This is the other

where are the pipes from?

image1 07-07-2009 01:01 PM

Re: trio of trumps
 

Quote:

where are the pipes from?
egay, don't remember the seller though

jeep44 07-07-2009 01:14 PM

Re: trio of trumps
 

I like that look when the "shark Fin" is removed.

lackluster 07-07-2009 03:46 PM

Re: trio of trumps
 

I don't know how I missed this thread a month ago, but I actually did the same shark fin removal a couple months ago for the same reason, I like the look of it a little better without the filler. The weird thing is that even though I'd seen the bottom fin cut off I thought I was the only one rocking the shaved top fin and inner cover! I just pulled the timing gears out this morning and was thinking about drilling those out. Got a picture of the jig you used? I just want to make sure I get it perfect. Looks like you got a bit of work ahead of you! Good luck!


All times are GMT -5. The time now is 06:03 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.