The Jockey Journal Board

The Jockey Journal Board (https://www.jockeyjournal.com/forum/index.php)
-   The Board (https://www.jockeyjournal.com/forum/forumdisplay.php?f=2)
-   -   Home made workshop tools (https://www.jockeyjournal.com/forum/showthread.php?t=25744)

RAZ 11-28-2007 12:12 AM

Re: Home made workshop tools
 

F.st.m. can you give us some more detail on the phase converter?
http://i110.photobucket.com/albums/n...e/HPIM1492.jpg

F.St.M. 11-28-2007 10:15 AM

Re: Home made workshop tools
 

Sure Raz,

First single phase (2 hot legs) enters the knife switch box at the bottom of the box. Leg #2 is jumped(split) to power up what will become the third leg. Time-delay fuses are installed so that the breaker doesn't trip during initial start-up.

http://i110.photobucket.com/albums/n...e/HPIM1502.jpg

Then the third leg power is sent down to a start capacitor. It returns up and into the momentary (light switch) switch. It then goes down and "bump starts" the idler motor which is bolted to the side of my mill.

With zero load on the idler motor, it creates a steady third leg (L3) which can now be used by the mill & lathe.

http://i110.photobucket.com/albums/n...e/HPIM1505.jpg

Though still a bit messy, the circuits can be identified on the wall board in this last photo. When running only one machine, the circuits (L1, L2, & l3) are very well ballanced and the "created 3rd leg" is at 92% - 96% amperage which is just about perfect. When running both(mill & lathe) machines simultaneously, amperage on L3 drops to 88% so I just plug in to the dayton run cap (blue star in photo) and this brings it back up to 95%.

http://i110.photobucket.com/albums/n...e/HPIM1507.jpg

Total expenses were $80 this includes the idler motor(ebay), fuses, romex, capacitors, and light switch. The knife switch came with the mill when I got it, so that was a freebie.

Jeff L 11-28-2007 11:15 AM

Re: Home made workshop tools
 

I converted a 9" benchtop drill press into a makeshift vertical lathe for polishing aluminum tubing.A live center on the bottom & a bow roller off a boat trailer that I cut in half & reshaped on the top.

scootermcrad 11-28-2007 01:34 PM

Re: Home made workshop tools
 

Quote:

Originally Posted by Jeff L (Post 241197)
I converted a 9" benchtop drill press into a makeshift vertical lathe for polishing aluminum tubing.A live center on the bottom & a bow roller off a boat trailer that I cut in half & reshaped on the top.

OH HEY!! That's a great idea!!!

1fastfx 11-28-2007 10:23 PM

Re: Home made workshop tools
 

Quote:

Originally Posted by F.St.M. (Post 241179)
Sure Raz,

First single phase (2 hot legs) enters the knife switch box at the bottom of the box. Leg #2 is jumped(split) to power up what will become the third leg. Time-delay fuses are installed so that the breaker doesn't trip during initial start-up.

http://i110.photobucket.com/albums/n...e/HPIM1502.jpg

Then the third leg power is sent down to a start capacitor. It returns up and into the momentary (light switch) switch. It then goes down and "bump starts" the idler motor which is bolted to the side of my mill.

With zero load on the idler motor, it creates a steady third leg (L3) which can now be used by the mill & lathe.

http://i110.photobucket.com/albums/n...e/HPIM1505.jpg

Though still a bit messy, the circuits can be identified on the wall board in this last photo. When running only one machine, the circuits (L1, L2, & l3) are very well ballanced and the "created 3rd leg" is at 92% - 96% amperage which is just about perfect. When running both(mill & lathe) machines simultaneously, amperage on L3 drops to 88% so I just plug in to the dayton run cap (blue star in photo) and this brings it back up to 95%.

http://i110.photobucket.com/albums/n...e/HPIM1507.jpg

Total expenses were $80 this includes the idler motor(ebay), fuses, romex, capacitors, and light switch. The knife switch came with the mill when I got it, so that was a freebie.

I have heard of this done before but nobody explained it as well as you have.Nice job ,esp when multible applications are needed.I have printed this and put in my notes for future reference.....Thanks

VA Rebel 11-28-2007 11:10 PM

Re: Home made workshop tools
 

F.St.M.

I applaud your make do creativity, but your electrical installation is a disaster.

Get an enclosure for those live parts before someone gets zapped. Those lugs are an electrocution hazzard, especially with either motor under load.

Pearson Customs 11-29-2007 01:07 AM

Re: Home made workshop tools
 

1 Attachment(s)
Here is my home made mill, back in trade school each of us made parts and then we all put them together and we each had a mill.
Chad
www.pearsoncustoms.com

kbg 11-29-2007 01:31 AM

Re: Home made workshop tools
 

wheeling machines, got plans off internet, made two one paid for
mine.
http://i182.photobucket.com/albums/x...ns/WHEELER.jpg

Dan 11-29-2007 10:59 AM

Re: Home made workshop tools
 

a stand for holding stuff, the arms adjust vert. and horizontaly

http://i25.photobucket.com/albums/c8...intpics002.jpg


neck fixture for an as yet unfinished frame jig


http://i25.photobucket.com/albums/c8...ramejig001.jpg


probably too dark to see but a combo wheel chock / tie down

http://i25.photobucket.com/albums/c8...masbday026.jpg


over center bike lift

http://i25.photobucket.com/albums/c8...ikelift002.jpg

some mods to a HF tubing notcherhttp://i25.photobucket.com/albums/c8...ikelift001.jpg

kids in shop class using a T-dolly
http://i25.photobucket.com/albums/c8...opclass006.jpg

this table has been one of the most useful things ever, has casters and makes moving things around the shop super easy, a '26 roadster is sitting on it now and I just push it around the shop
http://i25.photobucket.com/albums/c8...ter2006022.jpg

homemade Les Paul :)
http://i25.photobucket.com/albums/c80/Danjc/lp2.jpg

Dan 11-30-2007 10:01 AM

Re: Home made workshop tools
 

The thing was actually pretty decent for a HF tool right out of the box. The only things I did were mount it to a good heavy base (I built a wood one first but the 1/4" steel plate is much better). The biggest problem I found is that the pipe clamp didnt quite line up with quill, hole would be drilled off center. All I had to do was put some shim stock between the pipe clamp (the black piece) and the frame (the gray piece) to line it up. I think the biggest secret to making it work is good hole saws.

ca180 12-15-2007 11:43 PM

Re: Home made workshop tools
 

2 Attachment(s)
Just found this online... Guy says its for forming tunnels for bike gas tanks.

caschnd1 12-15-2007 11:53 PM

Re: Home made workshop tools
 

I use this tool to pressure test my intake manifold. Super easy to find even the smallest leaks.

http://i208.photobucket.com/albums/b...1/DCP_3310.jpg

http://i208.photobucket.com/albums/b...1/DCP_3311.jpg
  1. Remove the carb
  2. Bolt this onto the end of the intake using the rubber inner tube "gasket" to seal it up.
  3. Put my air compressor hose on the nipple and adjust the regulator to 10psi.
  4. Spray all around the intake o-rings with water with a little bit of dish soap.
If you have a leak, you'll get lots of bubbles. Much more reliable way to find intake leaks then spraying around the intake with WD40 or carb cleaner.

-Craig

ca180 12-16-2007 12:03 AM

Re: Home made workshop tools
 

Good Idea, I need to make one of those

Concrete B 09-25-2008 10:10 AM

Re: Home made workshop tools
 

I've been in the mood to make some items for the garage. I'll get pics of my metal brakes, english wheel, and parts washer and post them up. In the mean time....bump.

JeffO 09-26-2008 02:10 AM

Re: Home made workshop tools
 

great scott 1.21 jigawatts
Quote:

Originally Posted by RAZ (Post 241090)
F.st.m. can you give us some more detail on the phase converter?
http://i110.photobucket.com/albums/n...e/HPIM1492.jpg


F.St.M. 09-26-2008 08:50 AM

Re: Home made workshop tools
 

Quote:

Originally Posted by VA Rebel (Post 241469)
F.St.M.

I applaud your make do creativity, but your electrical installation is a disaster.

Get an enclosure for those live parts before someone gets zapped. Those lugs are an electrocution hazzard, especially with either motor under load.

I usualy try to avoid licking the live lugs on the wall when I'm machining something, so enclosing them is not a concern.

Brass Brawler 09-26-2008 09:26 AM

Re: Home made workshop tools
 

Quote:

Originally Posted by JeffO (Post 396014)
great scott 1.21 jigawatts

It still amazes me that "Doc" Brown could build a time machine, but lack the necessary skills to pronounce gigawatt....

Markee 09-26-2008 11:52 AM

Re: Home made workshop tools
 

When you build time machines at 60 years old, who has the time to learn spelling and pronunciations.

Bumpstick 09-26-2008 01:18 PM

Re: Home made workshop tools
 

My "poorman's" wheel clamp. I know, I need to turn the heat up on my welder. Hahaha...

http://i25.photobucket.com/albums/c9...ick/CHOCK1.jpg

http://i25.photobucket.com/albums/c9...ick/CHOCK2.jpg

The tried and true 'block of wood' but with channels drilled for a lil' added stability. Clamp a 2x4 to a 6x4 use a 1-3/8" bit at the seam and you get a perfect channel for the frame. 'b'

http://i25.photobucket.com/albums/c9...ick/block1.jpg

buckman50 09-26-2008 04:11 PM

Re: Home made workshop tools
 

Quote:

Originally Posted by JeffO (Post 396014)
great scott 1.21 jigawatts

Im convinced Doc Brown...errr Fritz...has plans for the flux capacitor buried somewhere in his shop.


All times are GMT -5. The time now is 06:15 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.